• Please read the whole manual before you install any mirror.
  • Do not use abrasive products or products for cleaning windows or kitchen.
  • Do not use cloths or anything that may scratch the mirror surface.

Important: If the mirrors are not to be installed within a short period of time, they should be stored flat on the floor. Storing them vertically may deform the wood board, and they may not be able to be installed correctly later on.

Straight mirror:

Dimensions (high × width): Big mirror: 110cmW  × 115cmH  / Small mirror: 86cm W × 115cmH

  • Material 3mm acrylic mirror.
  • Wooden rear panel 8mm.

Convex mirror:

Dimensions (high × width): Big mirror: 110cmW  × 115cm/105cmhH (Height is different on each side) / Small mirror: 86cm W × 115cm/105cmhH (Height is different on each side) 

  • Material 3mm acrylic mirror.
  • Wooden rear panel 8mm.

Mirrors boost mobility, self-awareness and joint attention while they multiply the stimulation provided by any visual element. Use it with the corner bases for the bubble tubes.

Product Introduction

  • Acrylic mirrors are special plastic mirrors used for reflecting bubble tubes and other elements in a multisensory room.
  • They are specially designed to be safe and durable under demanding environments.
  • The plastic material helps preventing breakage and accidents.
  • They are reinforced with a wooden panel to prevent warping and to ensure durability.
  • The edges are coated with a plastic material to avoid cuts and improve aesthetics.
  • They are easy to install without protruding from the wall.

Components

  1. Metracrylate mirror with wooden back pannel, and fixing holes
  2. Flexible PVC profile (for the edges that are not seen and are not protected by padded elements of the environment).

1.             2.

Tools Needed:

  • Drill and 6 mm bit
  • 2 anchors (number 6)
  • 2 Screws
  • Pencil
  • Tape measure
  • Level
  • Pliers

1. Installing the protective profiles

The profiles should be installed along the entire length of the upper edges of the mirrors and on the sides that are visible.

To ensure that the corner is correctly installed, it is necessary to measure the length of the upper edge and make a right-angle notch with the pliers, as shown in the picture.

2. Hanging mirrors on the wall

  • Locate the mirror according to the mounting position to check position.
  • Verify that the anchors are suitable for the type of wall where the mirror will be hung.

Note: if the mirror is installed along BJLive’s modular furniture: 

– The maximum mirror height on the wall should be 150cm

– The 5cm from the bottom of the mirror should be hidden behind the modules

A) Setup of the mirrors next to curved wall padding

 

B) Setup of the mirrors next to straight wall padding

  • Mark on the wall the place to drill, accordingly with the position of the holes in the mirror that will accommodate the anchors.
  • Drill the wholes, introduce the anchor and tighten the screws. Make sure that the anchor is as close to the wall as possible.

  • Hang the mirror as shown in picture. It should be touching the wall, otherwise please tigthen the anchor closer tot the wall.
  • Remove the protection film
  • Place the furniture, pressing against the mirror
  • Use a soft clean cotton or wool cloth to remove solid debris attached to the mirror before cleaning the mirror.
  • Use a very soft clean cloth slightly moistened in mild soap. Repeatedly rinse the cloth to remove any dust that may be on the cloth.
  • Dry with a soft dry cloth. Avoid rubbing vigorously because it may scratch the mirror.

 

IMPORTANT:

  • Do not use abrasive products or products for cleaning windows or kitchen.
  • Do not use cloths or anything that may scratch the mirror surface.
  • To avoid possible damage to the environment or human health that represents the uncontrolled disposal of waste, separate these products from other types of waste and recycle them correctly. In this way, the sustainable reuse of material resources is promoted.
  • Private users can contact the establishment where they purchased the product or with the relevant local authorities to find out how and where they can take it to be subjected to environmentally friendly and safe recycling.

Within the statutory warranty period we undertake to rectify free of charge by repair or replacement any product defects arising from material or production faults.

Any unauthorized tampering with, or modifications to the product will annul this warranty.

This product complies with EU 2004/108/EC Directive requirements .

Declaration of conformity can be downloaded by clicking on the following link: bjliveat.com

 

If you find any damage or any material is missing please contact our technical service for assistance.

BJ Adaptaciones
C/ Mare de Déu del Coll, 70, Bajos
08023 Barcelona, España
Fono: +34 93 285 04 37
Fax: +34 93 553 56 34
e-Mail: info@bjliveat.com
www.bjliveat.com

Any damage or breakage caused during transport must be notified within three days of receipt.