To ensure the safe operation of the device it’s recommended to read this user manual completely before starting to use it.
Sizes: cama de 110 cm x 210 cm x 40 cm
The vinyl fabric used to manufacture the products meets the following requirements
The polyurethane foam and polyethylene foam are normalized to meet the highest standards of European legislation, both technically and environmentally.
The waterbed provides a warm and pleasant feeling that allows users to explore their body while experiencing a profound relaxation. The water’s temperature can be regulated with the included heater.
This equipment may include upon request, a vibrating system to which is it possible to connect any music player. It is accessible for mobile hoists.
Parts of the equipment
For the pre-installation of the product you will need:
Keep in mind that for filling the bed you will need a hose (not included) to a water supply.
STEP 1: Fitting the legs to the base of the bed
Follow the guide images that indicate how to assemble the legs; the black plastic ring is used to adjust the leg height to level the bed on the floor allowing small level adjustments to be made.
STEP2: Connecting the thermostat to the waterbed’s heater
Pass the cable (1) through the hole (2) and line up the connector on the cable (1) to connect to the thermostat (3).
IMPORTANT: Do not connect the water heater until the bed is completely full as it could cause a fire. Unplug the heater before emptying the bed.
STEP 3: Fitting the fluid collection canvas and the mattress inside the bed frame
Place the fluid collection canvas on the water heater and spread it around the whole of the inside to insulate the mattress from the electrical elements and from the bed’s wooden frame holding the entire edge down with the help of another person or using sealing strips.
On the insulating canvas, place the mattress with the filling inlet at a short end of the bed and facing upwards. Distribute the whole mattress evenly in the bed.
STEP 4: Filling the bed
IMPORTANT: Before filling the bed, place the structure in the final position in the room because once it is filled is almost impossible to move it without damaging the bed’s frame.
Open the screw-cap on the filling nozzle and the inner cap to insert the filler hose about 30 cm inside the filling nozzle and begin to fill the mattress.
If the hose has already been used, before inserting it into the mattress rinse the inside of the hose allowing water to run through it for 2 minutes making sure the water runs clear after this time (if it is still dirty, use another hose).
When half full, add two bottles of anti-algae treatment fluid.
Fill the mattress until it is 1 cm below the foam rubber frame edges. You can control the water level by stopping the filling and looking through the filling nozzle.
STEP 5: Bleeding the air from the mattress
Bleed the air from inside the mattress using the air bleed pump:
NOTE: If the waterbed makes a sloshing sound it means there is still air in the mattress. A well bled mattress makes no noise.
STEP 6: Installing the vibroacoustic system
Connect the vibro cable with speakon jack to the vibroacoustic amplifier as indicated in the amplifier’s manual.
Maintaining the water mattress
As tap water is not always of the best quality and to prevent algae growth and preserve the purity of the water, every 6 months a preservative product must be added (a small bottle is enough for 6 months’ protection, a large bottle can be added once a year). There is no need to empty and refill the mattress. After adding the preservative fluid you must bleed any air left inside using the air bleed pump.
Like a traditional bed, the bed must be aired daily.
We recommend you follow the instructions. If you do so, you will never have to replace the water. It is important to always use the same brand of preservative product because some products are not compatible.
Using different brands or a late addition of the product may cause an unpleasant smell. If this occurs it is recommended to change the water.
Cleaning the vinyl
The outside of the water container is maintained by regularly spraying a little vinyl cleaner on the mattress and rubbing with a dry cloth. If you follow this advice well, your water mattress will have a longer life expectancy because this removes any remains of perspiration. It is recommended to fit a mattress cover to absorb any sweat. The water mattress is made of vinyl and therefore cannot absorb sweat making it very hygienic.
A water mattress that has not been cleaned for a long time will be covered with grains of salt caused by the evaporation of perspiration.
IMPORTANT: It is not recommended to clean the water mattress with soap or household cleaners.
In case vibrating elements are not working, chek the correspondant troubbleshooting depending on the equipment:
a) For SHX Rack, go to BJ-EX02 troubbleshooting.
b) For SHX Compact o SHX Device, go to BJ-EX04 troubbleshooting.
c) For SHX Vibroacoustic Amplifier, go to BJ-EMAVIB troubbleshooting.
This vibration device CAN NOT be connected to a sound amplifier. Always connect a vibration amplifier that works within the range of frequencies that mark the technical specifications of this manual.
This element is designed to produce a vibration from an audio signal. You are not ready to play a sound. Even so, a sound can be felt through the vibration.
The temperature of each user must be adjusted to the user’s needs. An average recommended temperature could be around 28ºC.
It is not necessary to change all the water in the bed. Follow the instructions in the maintenance section to see how to have teh water in good hygienic conditions.
Due to the large amount of water, it takes a long time to heat the entire bed. For this reason, the heater must not be turned off. The thermostat will maintain the temperature of the bed.
Within the legal warranty period we agree to rectify for free by repairing or replacing defects in the product derived from defective materials or manufacturing defects.
Any unauthorised alteration or modifications to the product will void this warranty.