BJ Support » Waterbed

Safety warning

To ensure the safe operation of the device it’s recommended to read this user manual completely before starting to use it.

Always fill the bed when is located at its final position in the room.
During the installation of the bed, make sure the heater cable can not be pulled or crushed.
Never attempt to move or lift the bed once it’s full.
Do not install the water mattress on the bed structure directly. Always use the mattress liner.
During the filling of the bed, be present always to make sure the tube don’t come out and spill water.
Do not use the partially filled mattress.
Make sure there are no folds in the liner in the heater area.
Do not jump or play on the water bed.
Do not lie on the bed with any cutting items to avoid damaging the fabric of the bed.
Never connect the heater without water inside the bed.
Before emptying the bed, first disconnect the heater from the power supply.
Never touch the heater of the bed directly with naked hands.
If you notice that the heater cable is damaged, disconnect it and contact your after-sales service.
Do not handle the heater’s power cord with wet hands.
In the event of water leakage, disconnect the heater’s power cord from the plug.

Technical specifications

Sizes: cama de 110 cm x 210 cm x 40 cm

Heater:

Power supply: 230V 50Hz
Power: 240W

Structure: Built on phenolic marine board with high load and moisture resistance.

Fabrics:

The vinyl fabric used to manufacture the products meets the following requirements

Microbial tested resistance
Bacterial tested resistance
Fungal tested resistance
Abrasion tested resistance
Perspiration and human saliva tested resistance
Urine tested resistance
Blood tested resistance
Total weight: 620 g/m2
Thickness: 0.5 mm to 1 mm
Meets the REACH regulation
Fireproof material classification m2
Complies with EN71-3 Toy Safety
Excellent resistance to sun exposure

Foams:

The polyurethane foam and polyethylene foam are normalized to meet the highest standards of European legislation, both technically and environmentally.

Description

The waterbed provides a warm and pleasant feeling that allows users to explore their body while experiencing a profound relaxation. The water’s temperature can be regulated with the included heater.

Parts of the equipment

Foam bed
Water matress
Water heater
Timer
Air bleed pump
Anti-algae treatment fluid
8 x legs.

Pre-Installation

For the pre-installation of the product you will need:

Power socket 230V -50Hz

Keep in mind that for filling the bed you will need a hose (not included) to a water supply.

Installation

Installation

STEP 1: Fitting the legs to the base of the bed

Follow the guide images that indicate how to assemble the legs; the black plastic ring is used to adjust the leg height to level the bed on the floor allowing small level adjustments to be made.

STEP2: Connecting the thermostat to the waterbed’s heater

Pass the cable (1) through the hole (2) and line up the connector on the cable (1) to connect to the thermostat (3).

IMPORTANT: Do not connect the water heater until the bed is completely full as it could cause a fire. Unplug the heater before emptying the bed.

The heater manual contains important safety information. See the manual before filling the bed.
The heating process can last between 24 and 48 hours.

STEP 3: Fitting the fluid collection canvas and the mattress inside the bed frame

Place the fluid collection canvas on the water heater and spread it around the whole of the inside to insulate the mattress from the electrical elements and from the bed’s wooden frame holding the entire edge down with the help of another person or using sealing strips.

On the insulating canvas, place the mattress with the filling inlet at a short end of the bed and facing upwards. Distribute the whole mattress evenly in the bed.

STEP 4: Filling the bed

IMPORTANT: Before filling the bed, place the structure in the final position in the room because once it is filled is almost impossible to move it without damaging the bed’s frame.

Open the screw-cap on the filling nozzle and the inner cap to insert the filler hose about 30 cm inside the filling nozzle and begin to fill the mattress.

If the hose has already been used, before inserting it into the mattress rinse the inside of the hose allowing water to run through it for 2 minutes making sure the water runs clear after this time (if it is still dirty, use another hose).

When half full, add two bottles of anti-algae treatment fluid.

Fill the mattress until it is 1 cm below the foam rubber frame edges. You can control the water level by stopping the filling and looking through the filling nozzle.

STEP 5: Bleeding the air from the mattress

Bleed the air from inside the mattress using the air bleed pump:

Connect the air bleed pump by screwing it on to the mattress’ filling nozzle.
Raise the pump slightly and pump keeping the pump raised until a stream of water flows out of the end of the pump.

Once bled, gently lower the pump and unscrew it from the filling nozzle holding the filling nozzle in one hand and unscrewing the pump with the other.
Fit the rubber cap when the water inside is level with the filling nozzle and then fit the screw-cap. Dry any drops of water on the surface of the mattress with a damp cloth.

NOTE: If the waterbed makes a sloshing sound it means there is still air in the mattress. A well bled mattress makes no noise.

Startup

Make sure the bed is connected to the power supply.
Set the thermostat temperature to the desired value.
While the heater starts heating the water, the green green color of the thermostat should be on. Once the desired temperature has been reached, the led will turn off.
The thermostat powers the heater automatically to maintain the desired temperature.
During the first startup, the heater can take between 24/48 hours to heat up all the water in the bed. For this reason. Do not unplug the bed power during its daily use. It should only be disconnected during long periods of inactivity.

Maintenance

Maintaining the water mattress

As tap water is not always of the best quality and to prevent algae growth and preserve the purity of the water, every 6 months a preservative product must be added (a small bottle is enough for 6 months’ protection, a large bottle can be added once a year). There is no need to empty and refill the mattress. After adding the preservative fluid you must bleed any air left inside using the air bleed pump.

Like a traditional bed, the bed must be aired daily.

We recommend you follow the instructions. If you do so, you will never have to replace the water. It is important to always use the same brand of preservative product because some products are not compatible.

Using different brands or a late addition of the product may cause an unpleasant smell. If this occurs it is recommended to change the water.

Cleaning the vinyl

The outside of the water container is maintained by regularly spraying a little vinyl cleaner on the mattress and rubbing with a dry cloth. If you follow this advice well, your water mattress will have a longer life expectancy because this removes any remains of perspiration. It is recommended to fit a mattress cover to absorb any sweat. The water mattress is made of vinyl and therefore cannot absorb sweat making it very hygienic.

A water mattress that has not been cleaned for a long time will be covered with grains of salt caused by the evaporation of perspiration.

IMPORTANT: It is not recommended to clean the water mattress with soap or household cleaners.

Troubbleshooting

Water is not hot:

A temperature around 28ºC is recommended.
Make sure there is power on the wall plug where the bed is connected.
Check if the cable of the bed is connected to the power supply.
The heater is properly connected to the thermostat slot.

Once you have checked the above steps, you can turn up the temperature of the thermostat to check that the heater is connected.
When the temperature rises, the green led of the thermostat has to be turned on.
After a while, when this temperature has been reached, the green LED should turn off.
Remember to leave the thermostat at the desired temperature.

In the case that the mattress has a leak:

Disconnect the thermostat from the wall plug.
Empty the mattress completely and replace it with a new one.

FAQ's

What temperature is suitable to adjust in the thermostat?

The temperature of each user must be adjusted to the user’s needs. An average recommended temperature could be around 28ºC.

Is it necessary to change the water in the bed periodically?

It is not necessary to change all the water in the bed. Follow the instructions in the maintenance section to see how to have teh water in good hygienic conditions.

Is it necessary to disconnect the heating element at the end of each session?

Due to the large amount of water, it takes a long time to heat the entire bed. For this reason, the heater must not be turned off. The thermostat will maintain the temperature of the bed.

Recycling

To avoid possible damage to the environment or human health that represents the uncontrolled disposal of waste, separate these products from other types of waste and recycle them correctly. In this way, the sustainable reuse of material resources is promoted.
Private users can contact the establishment where they purchased the product or with the relevant local authorities to find out how and where they can take it to be subjected to environmentally friendly and safe recycling.

Waterbed